Toyota Yaris: Hood / Reassembly

Toyota Yaris XP210 (2020-2026) Reapir and Service Manual / Vehicle Exterior / Door / Hatch / Hood / Reassembly

REASSEMBLY

PROCEDURE

1. INSTALL HOOD BUMPER CUSHION

(a) Rotate clockwise to install the 2 hood bumper cushions.

2. INSTALL HOOD SUPPORT ASSEMBLY

(a) Engage the claws to install the hood support assembly.

3. INSTALL HOOD STAY HOLDER

(a) Engage the claws to install the hood stay holder.

4. INSTALL HOOD INSULATOR

(a) Engage the guides to install the hood insulator with 4 new clips.

    Adjustment

    ADJUSTMENT CAUTION / NOTICE / HINT *a Centering Bolt *b Standard Bolt HINT: Centering bolts are used to install the hood hinges and hood lock...

    Hood Lock Control Cable Assembly

    ..

    Other information:

    Toyota Yaris XP210 (2020-2026) Reapir and Service Manual: Terminals Of Ecu


    TERMINALS OF ECU TERMINALS OF ECU *a Component without harness connected (Skid Control ECU [Brake Actuator Assembly]) - - Terminal No. (Symbol) Terminal Description 1 (GND2) Pump motor ground 2 - (Not used) 3 - (Not used) 4 - (Not used) 5 (STP2) Stop light switch assembly input 6 - (Not used) 7 - (Not used) 8 - (Not used) 9 - (Not used) 10 (CANL) CAN communication line L 11 - (Not used) 12 (IGR) ECU power supply input 13 (BM) Motor relay power supply 14 (SP1) Speed signal output for speedometer 15 (RR-) Rear wheel speed RH (-) signal input 16 (RR+) Rear wheel speed RH (+) power supply output 17 (FL-) Front wheel speed LH (-) signal input 18 (FL+) Front wheel speed LH (+) power supply output 19 - (Not used) 20 - (Not used) 21 - (Not used) 22 (CANH) CAN communication line H 23 - (Not used) 24 - (Not used) 25 (GND1) Skid control ECU (brake actuator assembly) ground 26 (STPO) Stop light switch assembly output 27 - (Not used) 28 (RL-) Rear wheel speed LH (-) signal input 29 (RL+) Rear wheel speed LH (+) power supply output 30 (FR-) Front wheel speed RH (-) signal input 31 (FR+) Front wheel speed RH (+) power supply output 32 - (Not used) 33 (CSW) VSC OFF switch (combination switch assembly) input 34 - (Not used) 35 (STP) Stop light switch assembly input 36 (CA2H) CAN communication line H 37 (CA2L) CAN communication line L 38 (+BS) Solenoid relay power supply TERMINAL INSPECTION (a) Disconnect the A108 connector and measure the voltage or resistance on the wire harness side...

    Toyota Yaris XP210 (2020-2026) Owner's Manual: Gear Shift Indicator


    The gear shift indicator supports you to obtain optimum fuel economy and smooth driving. It displays the selected gear position in the combination meter as well as notifies the driver to change to the most suitable gear position corresponding to the actual driving condition...

    Categories

    Supplemental Restraint System (SRS) Precautions

    The front and side supplemental restraint systems (SRS) include different types of air bags. Please verify the different types of air bags which are equipped on your vehicle by locating the “SRS AIRBAG” location indicators. These indicators are visible in the area where the air bags are installed.

    The air bags are installed in the following locations:

    The steering wheel hub (driver air bag) The front passenger dashboard (front passenger air bag) The outboard sides of the front seatbacks (side air bags) The front and rear window pillars, and the roof edge along both sides (curtain air bags)

    read more

     
    Copyright © 2026 www.toyaris4.com