Toyota Yaris: G16e-gts (lubrication) / Lubrication System

Toyota Yaris XP210 (2020-2025) Reapir and Service Manual / Engine & Hybrid System / G16e-gts (lubrication) / Lubrication System

On-vehicle Inspection

ON-VEHICLE INSPECTION

PROCEDURE

1. CHECK ENGINE OIL LEVEL

(a) Warm up and stop the engine, then wait for 5 minutes.

(b) Check that the engine oil level is between the low level and full level marks on the engine oil level dipstick.

If the level is low, check for engine oil leaks and add engine oil to the full level mark.

NOTICE:

Do not fill to above the full level mark.

HINT:

A certain amount of engine oil will be consumed while driving. In the following situations, engine oil consumption may increase, and engine oil may need to be refilled in between oil maintenance intervals.

When the engine is new, for example directly after purchasing the vehicle or after replacing the engine.
If low quality engine oil or oil of an inappropriate viscosity is used.
When driving at high engine speeds or with a heavy load (when towing, etc.), or when accelerating or decelerating frequently while driving.
When idling for a long time, or when driving frequently through heavy traffic.

When judging the amount of oil consumption, keep in mind that the oil may have become diluted, making it difficult to judge the true level accurately.

2. CHECK ENGINE OIL QUALITY

(a) Check the engine oil for deterioration, water intrusion, discoloration or thinning.

If the quality is visibly poor, replace the engine oil and oil filter element.

3. INSPECT OIL PRESSURE

(a) Connect the GTS to the DLC3.

(b) Turn the ignition switch on (IG).

(d) Enter the following menus: Powertrain / Engine / Data List / Engine Speed, Engine Oil Temperature Sensor and Engine Oil Pressure.

Powertrain > Engine > Data List

Tester Display
Engine Speed
Engine Oil Temperature Sensor
Engine Oil Pressure

(e) Start the engine and warm it up until the engine oil temperature is 75 to 85°C (167 to 185°F).

(f) Read the Data List.

Standard

Engine Speed	Engine Oil Temperature Sensor	Engine Oil Pressure
1500 rpm	75 to 85°C (167 to 185°F)	100 kPa(gauge) [14.5 psi(gauge)] or higher
2500 rpm	75 to 85°C (167 to 185°F)	200 kPa(gauge) [29 psi(gauge)] or higher

If the result is not as specified, check the quality of the engine oil and check the oil paths for clogging. Repair or replace if necessary. After performing replacement or repairs, if the engine oil pressure is not as specified, perform the confirmation driving pattern for DTC P052400 in SFI System and check for DTCs.

Click here

Engine Oil Cooler

ComponentsCOMPONENTS ILLUSTRATION *1 OIL COOLER ASSEMBLY *2 OIL COOLER GASKET *3 NO. 5 WATER BY-PASS HOSE *4 OIL FILLER CAP ASSEMBLY *5 GASKET *6 OIL PAN DRAIN PLUG *7 NO...

Oil And Oil Filter

ComponentsCOMPONENTS ILLUSTRATION *1 OIL FILTER SUB-ASSEMBLY *2 OIL FILLER CAP SUB-ASSEMBLY *3 GASKET *4 OIL PAN DRAIN PLUG *5 REAR ENGINE UNDER COVER RH - - Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft...

Other information:

Toyota Yaris XP210 (2020-2025) Reapir and Service Manual: Starter Relay Circuit Short to Battery (P061512)

MONITOR DESCRIPTION While the engine is cranked, current flows from terminal STA2 of the engine stop and start ECU to terminal STA of the ECM (STA signal). If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit...

Toyota Yaris XP210 (2020-2025) Reapir and Service Manual: Brake Booster Pressure Sensor(running) (P055500,P05552A)

DESCRIPTION The engine stop and start ECU determines changes in the brake booster assembly pressure based on the voltage signal received from the vacuum sensor assembly in the brake booster assembly. If the output value of the vacuum sensor assembly remains the same even though the brake booster assembly pressure changes when the brake pedal is operated or the vehicle is being driven, the engine stop and start ECU judges that the sensor is stuck...