Toyota Yaris: Bluetooth® / Voice Recognition
In this section, the basic operation of the voice recognition is explained.
Activating Voice Recognition
Press the talk button.
Ending Voice Recognition
Use one of the following methods:
- Press the hang-up button.
- Say, “Cancel”.
- Operate the commander switch or the center display (only when vehicle is stopped).
Skipping Voice Guidance (for faster operation)
Press and release the talk button.
Troubleshooting for Voice Recognition
If you do not understand an operation method while in the voice recognition mode, say “Tutorial” or “Help”.
Commands useable anytime during voice recognition
“Go Back” and “Cancel” are commands which can be used at anytime during voice recognition.
- Returning to previous operation
To return to the previous operation, say, “Go Back” while in voice recognition mode.
- Cancel
To put the Bluetooth® Hands-Free system in standby mode, say, “Cancel” while in voice recognition mode.
To prevent a deterioration in the voice recognition rate and voice quality, the following points should be observed:
- The voice recognition cannot be performed while voice guidance or the beep sound is operating. Wait until the voice guidance or the beep sound is finished before saying your commands.
- Phone related commands are available only when your phone is connected via Bluetooth®. Make sure your phone is connected via Bluetooth® before you operate phone related voice commands.
- Music play commands, such as Play Artist and Play Album can be used only in USB audio mode.
- Do not speak too slowly or loudly (no loud voice).
- Speak clearly, without pausing between words or numbers.
- Dialects or different wording other than hands-free prompts cannot be recognized by voice recognition. Speak in the wording specified by the voice commands.
- It is not necessary to face the microphone or approach it. Speak the voice commands while maintaining a safe driving position.
- Close the windows to reduce loud noises from outside the vehicle, or turn down the airflow of the air-conditioning system while Bluetooth® Hands-Free is being used.
- Make sure the vents are not directing air up towards the microphone.
If the voice recognition performance is not satisfactory. Refer to Troubleshooting.
Voice Command List
Voice command
When the talk button is pressed and the following command is spoken, the
audio or navigation can be operated. The commands in the () can be omitted...
Other information:
Toyota Yaris XP210 (2020-2026) Reapir and Service Manual: Fail-safe Chart
FAIL-SAFE CHART If any of the following DTCs are stored, the engine stop and start ECU enters fail-safe mode to preserve vehicle operability. DTC Component Fail-safe Operation Fail-safe Deactivation Condition P033562 Open in engine speed signal circuit Stop and start control is prohibited Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control All of the following conditions are met for 10 seconds: Normal communication with ECM Engine speed 500 rpm or higher Engine speed (communication signal) 500 rpm or higher Difference between engine speed from pulse signal and engine speed from communication signal is less than 100 rpm P055500 P05552A Vacuum sensor assembly Brake booster assembly Vacuum hose (brake booster hose) Stop and start control is prohibited Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control One of the following conditions is met: Vacuum changes while the brake pedal is depressed Vacuum changes a specified number of times while the vehicle is being driven faster than a certain vehicle speed P055511 P055515 Vacuum sensor assembly circuit Stop and start control is prohibited Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control Sensor output is within standard range P060629 Engine stop and start ECU Stop and start control is prohibited Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control Pass condition detected and ignition switch turned to ON P060B1C P060B49 P060B71 Analog to digital converter (Engine stop and start ECU) Stop and start control is prohibited Engine is automatically restarted if a DTC is stored while the engine is stopped by stop and start control Pass condition detected and ignition switch turned to ON P061519 ST NO...
Toyota Yaris XP210 (2020-2026) Reapir and Service Manual: Components
COMPONENTS ILLUSTRATION *1 OUTPUT SHAFT BEARING SHAFT SNAP RING *2 NEEDLE ROLLER BEARING *3 SYNCHRONIZER SHIFTING KEY SPRING *4 SHAFT SNAP RING *5 SPACER *6 BALL *7 OUTPUT SHAFT FRONT BEARING INNER RACE *8 SYNCHROMESH SHIFTING KEY BALL *9 NO...
Categories
- Manuals Home
- Toyota Yaris Owners Manual
- Toyota Yaris Service Manual
- Brake System Control Module "A" System Voltage System Voltage Low (C137BA2)
- How to use USB mode
- Auto Lock/Unlock Function
- New on site
- Most important about car
Fuel Gauge
The fuel gauge shows approximately how much fuel is remaining in the tank when the ignition is switched ON. We recommend keeping the tank over 1/4 full.
