Toyota Yaris: Wiper And Washer System / Operation Check

Toyota Yaris XP210 (2020-2026) Reapir and Service Manual / Vehicle Exterior / Wiper / Washer / Wiper And Washer System / Operation Check

OPERATION CHECK

CHECK FRONT WIPER CONTROL

(a) Auto wiper function

(1) Continuously apply water to the windshield glass in front of the rain sensor.

(2) Turn the ignition switch to ON.

(3) Move the front wiper switch to the AUTO position.

(4) Check that the front wipers operate.

(b) Intermittent control function

HINT:

When the AUTO wiper function is disabled through a customize setting, the intermittent control function can be operated.

Click here

(1) Turn the ignition switch to ON.

(2) Move the front wiper switch to the AUTO position.

(3) Check that the intermittent operation interval can be adjusted between approximately 4 and 12.5 seconds by operating the auto sensitivity adjustment switch.

(c) Vehicle speed sensing type adjustable intermittent wiper control function

HINT:

When the AUTO wiper function is disabled through a customize setting, the intermittent control function can be operated.

Click here

(1) Turn the ignition switch to ON.

(2) Move the front wiper switch to the AUTO position.

(3) Check that the intermittent operation interval changes between approximately 1.5 and 11 seconds according to the vehicle speed and the position of the auto sensitivity adjustment switch.

CHECK WASHER CONTROL

(a) Front washer cooperation

(1) Turn the ignition switch to ON.

(2) Hold the washer switch in the Fr WASH position for approximately 0.5 seconds or more and check that the front wipers operate in LO and washer fluid is sprayed.

(3) Release the washer switch and check that the front wipers operate for 3 cycles.

(b) Drip prevention wiper function

NOTICE:

Perform this inspection with the vehicle stopped.

(1) Turn the ignition switch to ON.

(2) Operate the washers and check that approximately 3 seconds after washer cooperation operates, the wipers operate 1 cycle.

    Customize Parameters

    CUSTOMIZE PARAMETERS CUSTOMIZE WIPER AND WASHER SYSTEM NOTICE: When the customer requests a change in a function, first make sure that the function can be customized...

    Utility

    UTILITY WIPER SPECIFICATION SWITCH HINT: Although this item is displayed on the GTS, it is not applicable to this vehicle. (a) According to the display on the GTS, select Wiper Specification Switch...

    Other information:

    Toyota Yaris XP210 (2020-2026) Reapir and Service Manual: Lack of Power


    DESCRIPTION Problem Symptom Suspected Area Trouble Area Engine speed fluctuation due to abnormal combustion Idle speed too low or high Strong engine vibration due to above symptoms Ignition malfunction Deviation in air fuel ratio (Excessive or insufficient intake air volume or fuel supply) Insufficient compression Changes in load from another system Ignition system Spark plug Ignition coil assembly Fuel system Direct fuel injector assembly Port fuel injector assembly Fuel pump assembly (for high pressure side) Fuel pump (for low pressure side) Fuel pump control circuit Fuel suction plate sub-assembly Fuel main valve assembly Fuel line Purge VSV system Fuel quality (existence of foreign matter, degradation) Intake and exhaust systems Mass air flow meter sub-assembly Intake system (Air leaks or deposit accumulation) Throttle body with motor assembly Air fuel ratio sensor (sensor 1) Air fuel ratio sensor (sensor 2) Cam timing oil control solenoid assembly Variable Valve Timing system (VVT system) Other control systems ECM Wire harness or connector Knock control sensor Engine coolant temperature sensor Engine Water control valve Engine assembly High load from another system Air conditioning system Power steering system Electrical load signal system SYMPTOM AND CAUSE OF SYSTEM MALFUNCTION HINT: The following are descriptions of the characteristics of each system malfunction...

    Toyota Yaris XP210 (2020-2026) Reapir and Service Manual: Adjustment


    ADJUSTMENT CAUTION / NOTICE / HINT The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after completing the rear wheel alignment procedure are shown below. Necessary Procedures After Procedure Performed Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link Rear wheel alignment adjustment ECU Data Initialization Active torque split AWD system Calibration DTCs are stored Slip indicator light illuminates VSC disabled or malfunctions PROCEDURE 1...

    Categories

    Front Seat Belt Pretensioners

    The front seat belt pretensioners are designed to deploy in moderate or severe frontal, near frontal collisions.

    In addition, the pretensioners operate when a side collision or a rollover accident is detected. The pretensioners operate differently depending on what types of air bags are equipped. For more details about the seat belt pretensioner operation, refer to the SRS Air Bag Deployment Criteria.

    read more

     
    Copyright © 2026 www.toyaris4.com