Toyota Yaris: Wiper And Washer System / Customize Parameters

Toyota Yaris XP210 (2020-2026) Reapir and Service Manual / Vehicle Exterior / Wiper / Washer / Wiper And Washer System / Customize Parameters

CUSTOMIZE PARAMETERS

CUSTOMIZE WIPER AND WASHER SYSTEM

NOTICE:

When the customer requests a change in a function, first make sure that the function can be customized.
Be sure to make a note of the current settings before customizing.
When troubleshooting a function, first make sure that the function is set to the default setting.

HINT:

The following items can be customized.

(a) Select the setting by referring to the table below.

Wiper

Tester Display	Description	Default	Setting	ECU
R Wiper Stop Function at Back Door/Trunk Lid Open	Function to enable the back door open linked rear wiper suspend function*1	Disable	$00:Enable,$01:Disable	Main body ECU (Multiplex network body ECU)
Rear Wiper Washer Function	Function to enable the rear washer linked rear wiper operation function*1	Enable	$00:Enable,$01:Disable	Main body ECU (Multiplex network body ECU)
Rear Wiper with Reverse Setting	Function to enable the R shift position linked rear wiper operation function*1	1time	$00:Disable,$02:1 time,$03:Continuation	Main body ECU (Multiplex network body ECU)
Auto Wiper	Function to enable AUTO wiper operation	Avail	0:Avail,1:Not Avl	Rain sensor

*1: Although the item is displayed on the GTS, it is not applicable to this vehicle.

HINT:

Changes to the customize settings will not be applied until the ignition switch is turned off then ON.

How To Proceed With Troubleshooting

CAUTION / NOTICE / HINT HINT: Use the following procedure to troubleshoot the wiper and washer system. *: Use the GTS. PROCEDURE 1. VEHICLE BROUGHT TO WORKSHOP NEXT 2...

Operation Check

OPERATION CHECK CHECK FRONT WIPER CONTROL (a) Auto wiper function (1) Continuously apply water to the windshield glass in front of the rain sensor. (2) Turn the ignition switch to ON...

Other information:

Toyota Yaris XP210 (2020-2026) Reapir and Service Manual: Replacement

REPLACEMENT CAUTION / NOTICE / HINT The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during diaphragm oil seal replacement are shown below. Necessary Procedure After Parts Removed/Installed/Replaced Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link Gas leaks from exhaust system Inspection after repair Poor idle, etc...

Toyota Yaris XP210 (2020-2026) Reapir and Service Manual: Inspection

INSPECTION PROCEDURE 1. INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY (a) Check the resistance. (1) Measure the resistance according to the value(s) in the table below. Standard Resistance: Front Wiper Switch Tester Connection Condition Specified Condition z5-14 (MIST) -z5-5 (E) MIST position Below 1 Ω z5-14 (MIST) -z5-5 (E) Except MIST position 10 kΩ or higher z5-10 (W_OFF) - z5-5 (E) OFF position Below 1 Ω z5-10 (W_OFF) - z5-5 (E) Except OFF position 10 kΩ or higher z5-13 (+S) - z5-5 (E) AUTO position Below 1 Ω z5-13 (+S) - z5-5 (E) Except AUTO position 10 kΩ or higher z5-11 (+1) - z5-5 (E) LO position Below 1 Ω z5-11 (+1) - z5-5 (E) Except LO position 10 kΩ or higher z5-12 (+2) - z5-5 (E) HI position Below 1 Ω z5-12 (+2) - z5-5 (E) Except HI position 10 kΩ or higher Front Washer Switch Tester Connection Condition Specified Condition z5-15 (WF) - z5-5 (E) ON position Below 1 Ω z5-15 (WF) - z5-5 (E) OFF position 10 kΩ or higher Auto Sensitivity Adjustment Switch Tester Connection Condition Specified Condition z5-4 (VR) - z5-5 (E) P1 position 1102 to 1218 Ω z5-4 (VR) - z5-5 (E) P2 position 570 to 630 Ω z5-4 (VR) - z5-5 (E) P3 position 256...