Toyota Yaris: Sfi System / Lost Communication with Stop and Start Control Module Missing Message (U110387)

1. Connect the GTS to the DLC3.
2. Turn the ignition switch to ON.
3. Turn the GTS on.
4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
5. Turn the ignition switch off and wait for at least 30 seconds.
6. Turn the ignition switch to ON.
7. Turn the GTS on.
8. Wait 5 seconds or more.
9. Enter the following menus: Powertrain / Engine / Trouble Codes.
10. Read the DTCs.

    HINT:

    • If a pending DTC is output, the system is malfunctioning.
    • If a pending DTC is not output, perform the following procedure.
11. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
12. Input the DTC: U110387.
13. Check the DTC judgment result.

    GTS Display	Description
    NORMAL	DTC judgment completed System normal
    ABNORMAL	DTC judgment completed System abnormal
    INCOMPLETE	DTC judgment not completed Perform driving pattern after confirming DTC enabling conditions

    HINT:

    • If the judgment result shows NORMAL, the system is normal.
    • If the judgment result shows ABNORMAL, the system has a malfunction.

Lost Communication with Brake System Control Module Missing Message (U012987)

MONITOR DESCRIPTION The ECM and skid control ECU (brake actuator assembly) send and receive signals via CAN communication. If a communication error occurs between the ECM and skid control ECU (brake actuator assembly), the ECM stores this DTC...

Turbocharger Oil Leak and White Smoke

DESCRIPTION Type of Oil Leak Outline Major Trouble Area Internal oil leak (white smoke) Oil leak from the bearing housing into the compressor housing (intake side) or turbine housing (exhaust side) through the seal ring...

Other information:

Toyota Yaris XP210 (2020-2026) Reapir and Service Manual: Removal

REMOVAL CAUTION / NOTICE / HINT The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the rear No. 1 differential mount cushion replacement are shown below...

Toyota Yaris XP210 (2020-2026) Reapir and Service Manual: Inspection

INSPECTION PROCEDURE 1. INSPECT TURN SIGNAL SWITCH (a) Check the resistance. (1) Measure the resistance according to the value(s) in the table below. Standard Resistance: Light Control Switch Tester Connection Condition Specified Condition z6-7 (A) - z6-5 (EL) Light control switch in AUTO position Below 1 Ω z6-3 (T) - z6-5 (EL) Light control switch in tail position Below 1 Ω z6-12 (H) - z6-5 (EL) Light control switch in head position Below 1 Ω Dimmer Passing Switch Tester Connection Condition Specified Condition z6-11 (HF) - z6-5 (EL) Dimmer switch in high flash position Below 1 Ω z6-16 (HU) - z6-5 (EL) Dimmer switch in high position Below 1 Ω Fog Light Switch Tester Connection Condition Specified Condition z6-4 (B) - z6-5 (EL) Fog light switch in rear position Below 1 Ω z6-13 (BFG) - z6-5 (EL) Fog light switch in front position Below 1 Ω Turn Signal Switch Tester Connection Condition Specified Condition z6-8 (TR) - z6-5 (EL) Turn signal switch in neutral position 10 kΩ or higher z6-14 (TL) - z6-5 (EL) Turn signal switch in neutral position 10 kΩ or higher z6-8 (TR) - z6-5 (EL) Turn signal switch in right turn position Below 1 Ω z6-8 (TR) - z6-5 (EL) Turn signal switch in full right turn position Below 1 Ω z6-8 (TR) - z6-6 (CR) Turn signal switch in full right turn position Below 1 Ω z6-6 (CR) - z6-5 (EL) Turn signal switch in full right turn position Below 1 Ω z6-14 (TL) - z6-5 (EL) Turn signal switch in left turn position Below 1 Ω z6-14 (TL) - z6-5 (EL) Turn signal switch in full left turn position Below 1 Ω z6-14 (TL) - z6-6 (CR) Turn signal switch in full left turn position Below 1 Ω z6-6 (CR) - z6-5 (EL) Turn signal switch in full left turn position Below 1 Ω If the result is not as specified, replace the turn signal switch...