Toyota Yaris: Lin Communication System / Diagnostic Trouble Code Chart

Toyota Yaris XP210 (2020-2026) Reapir and Service Manual / Power Source & Network / Networking / Lin Communication System / Diagnostic Trouble Code Chart

DIAGNOSTIC TROUBLE CODE CHART

LIN Communication System

DTC No.	Detection Item	Link
B120687	P/W Master SW System Missing Message
B228787	LIN Communication Missing Message
B232187	D-Door P/W System Missing Message
B232287	P-Door P/W System Missing Message
B232588	Door LIN Bus off
B278187	Steering Lock System Missing Message
B278588	Communication between ECUs connected by LIN Bus off
B278987	ID-BOX Missing Message
B278C87	Power Source Control System Missing Message

Data List / Active Test

DATA LIST / ACTIVE TEST DATA LIST HINT: Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts...

P/W Master SW System Missing Message (B120687,B232187,B232287)

DESCRIPTION This DTC is stored when LIN communication between the main body ECU (multiplex network body ECU) and multiplex network master switch assembly, front power window regulator motor assembly (driver door), front power window regulator motor assembly (front passenger door) stops for 10 seconds or more...

Other information:

Toyota Yaris XP210 (2020-2026) Reapir and Service Manual: How To Proceed With Troubleshooting

CAUTION / NOTICE / HINT HINT: Use the following procedure listed to troubleshoot the Active Torque Split AWD System. *: Use the GTS. PROCEDURE 1. VEHICLE BROUGHT TO WORKSHOP NEXT 2. INSPECT AUXILIARY BATTERY VOLTAGE Standard voltage: 11 to 14 V If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step...

Toyota Yaris XP210 (2020-2026) Reapir and Service Manual: Terminals Of Ecu

TERMINALS OF ECU TERMINALS OF ECU *a Component without harness connected (Skid Control ECU [Brake Actuator Assembly]) - - Terminal No. (Symbol) Terminal Description 1 (GND2) Pump motor ground 2 - (Not used) 3 - (Not used) 4 - (Not used) 5 (STP2) Stop light switch assembly input 6 - (Not used) 7 - (Not used) 8 - (Not used) 9 - (Not used) 10 (CANL) CAN communication line L 11 - (Not used) 12 (IGR) ECU power supply input 13 (BM) Motor relay power supply 14 (SP1) Speed signal output for speedometer 15 (RR-) Rear wheel speed RH (-) signal input 16 (RR+) Rear wheel speed RH (+) power supply output 17 (FL-) Front wheel speed LH (-) signal input 18 (FL+) Front wheel speed LH (+) power supply output 19 - (Not used) 20 - (Not used) 21 - (Not used) 22 (CANH) CAN communication line H 23 - (Not used) 24 - (Not used) 25 (GND1) Skid control ECU (brake actuator assembly) ground 26 (STPO) Stop light switch assembly output 27 - (Not used) 28 (RL-) Rear wheel speed LH (-) signal input 29 (RL+) Rear wheel speed LH (+) power supply output 30 (FR-) Front wheel speed RH (-) signal input 31 (FR+) Front wheel speed RH (+) power supply output 32 - (Not used) 33 (CSW) VSC OFF switch (combination switch assembly) input 34 - (Not used) 35 (STP) Stop light switch assembly input 36 (CA2H) CAN communication line H 37 (CA2L) CAN communication line L 38 (+BS) Solenoid relay power supply TERMINAL INSPECTION (a) Disconnect the A108 connector and measure the voltage or resistance on the wire harness side...