Toyota Yaris: Active Noise Control System / Data List / Active Test

Toyota Yaris XP210 (2020-2024) Reapir and Service Manual / Audio & Visual & Telematics / Audio / Video / Active Noise Control System / Data List / Active Test

DATA LIST / ACTIVE TEST

DATA LIST

NOTICE:

In the following table, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

(a) Enter the following menus: Body Electrical / Active Noise Control / Data List.

(b) Read the Data List according to the display on the GTS.

Body Electrical > Active Noise Control > Data List

Tester Display	Measurement Item	Range	Reference Value	Diagnostic Note
Total Distance Traveled	Displays the current total driving distance	0 to 16777215	Equivalent to the actual total driving distance	Refer to the Total Distance Traveled - Unit for the units
Total Distance Traveled - Unit	Displays the current total driving distance units	km or mile	Units according destination	-
ANC Function/ESE Function	ANC function and ESE function setting status (ON/OFF)	ANC(OFF)/ESE(OFF), ANC(ON)/ESE(OFF), ANC(OFF)/ESE(ON), ANC(ON)/ESE(ON)	Customized setting display	-

ACTIVE TEST

HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

(a) Enter the following menus: Body Electrical / Active Noise Control / Active Test.

(b) Perform the Active Test according to the display on the GTS.

Body Electrical > Active Noise Control > Active Test

Tester Display	Measurement Item	Control Range	Diagnostic Note
Sound (All CH)	Test sound outputs in following order: Front No. 1 speaker assembly LH → Front No. 1 speaker assembly RH → Rear speaker assembly LH → Rear speaker assembly RH	ON or OFF	-
Sound "CH1"	Test sound output from front No. 1 speaker assembly LH	ON or OFF	-
Sound "CH2"	Test sound output from front No. 1 speaker assembly RH	ON or OFF	-
Sound "CH3"	Test sound output from Rear speaker assembly LH	ON or OFF	-
Sound "CH4"	Test sound output from Rear speaker assembly RH	ON or OFF	-

Freeze Frame Data

FREEZE FRAME DATA CHECK FREEZE FRAME DATA HINT: Whenever an active noise control system DTC is stored, the stereo component equalizer assembly stores the current vehicle state as freeze frame data...

Diagnostic Trouble Code Chart

D..

Other information:

Toyota Yaris XP210 (2020-2024) Owner's Manual: Outside Mirrors

Mirror type Flat type (driver’s side) Flat surface mirror. Convex type (front passenger side) The mirror has single curvature on its surface. Power mirror adjustment The ignition must be switched to ACC or ON position. To adjust: Rotate the mirror switch to the left or right to choose the left or right side mirror...

Toyota Yaris XP210 (2020-2024) Reapir and Service Manual: Fuel Pump Control General Electrical Failure (P12D501)

DESCRIPTION Refer to DTC P062712. Click here DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note P12D501 Fuel Pump Control General Electrical Failure When the fuel pump control ECU operation duty ratio is 3 to 65%, the fuel pump control ECU detects a short in the fuel pump circuit for 3 seconds or more (1 trip detection logic)...