Toyota Yaris: Active Torque Split Awd System / AWD Warning Light does not Come ON
DESCRIPTION
Refer to "AWD Warning Light Remains ON".
Click here
WIRING DIAGRAM
Refer to "AWD Warning Light Remains ON".
Click here
CAUTION / NOTICE / HINT
Refer to "AWD Warning Light Remains ON".
Click here
PROCEDURE
| 1. | CHECK HARNESS AND CONNECTOR |
(a) Check that there is no looseness at the locking and connecting parts of the AWD ECU assembly connector.
OK:
No looseness at the locking and connecting parts
(b) Disconnect the O119 and O120 AWD ECU assembly connectors.
(c) Check the connector case and the terminal for deformation and corrosion.
OK:
No deformation or corrosion
(d) Connect the O119 and O120 AWD ECU assembly connectors.
| NG |
 | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
| 2. | CHECK AWD WARNING MESSAGE |
(a) According to the display on the GTS, perform the Active Test and check the Data List "AWD Warning Light" turns ON/OFF.
Chassis > Four Wheel Drive > Data List| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| 4WD Warning Light | AWD warning (multi-information display) | OFF / ON | OFF: Warning off ON: Warning on | - |
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| 4WD Warning Light | AWD warning (multi-information display) | Warning ON/OFF | Observe combination meter assembly |
| Active Test Display |
|---|
| 4WD Warning Light |
| Data List Display |
|---|
| 4WD Warning Light |
| Result | Proceed to |
|---|---|
| Data List display does not switch ON/OFF | A |
| Data List display switches ON/OFF | B |
| A |
 | REPLACE AWD ECU ASSEMBLY |
| B |
 | GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) |
AWD Warning Light Remains ON
DESCRIPTION The AWD ECU assembly is connected to the combination meter assembly via the CAN communication system. If the AWD ECU assembly stores any DTCs which are related to the active torque split AWD system, the warning message is displayed on the multi-information display in the combination meter assembly...
AWD Control Switch Circuit
DESCRIPTION Operate the AWD control switch (No. 2 combination switch assembly) and check that the Data List display and the messages in the multi-information display change according to the switch operation...
Other information:
Toyota Yaris XP210 (2020-2026) Reapir and Service Manual: Installation
INSTALLATION PROCEDURE 1. INSTALL ROOF ANTENNA ASSEMBLY (a) When reusing the roof antenna assembly: (1) Install a new seal. (b) Engage the guides and claws to install the roof antenna assembly to the antenna cover as shown in the illustration...
Toyota Yaris XP210 (2020-2026) Reapir and Service Manual: Inspection
INSPECTION PROCEDURE 1. INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY (a) Check the resistance. (1) Measure the resistance according to the value(s) in the table below. Standard Resistance: Front Wiper Switch Tester Connection Condition Specified Condition z5-14 (MIST) -z5-5 (E) MIST position Below 1 Ω z5-14 (MIST) -z5-5 (E) Except MIST position 10 kΩ or higher z5-10 (W_OFF) - z5-5 (E) OFF position Below 1 Ω z5-10 (W_OFF) - z5-5 (E) Except OFF position 10 kΩ or higher z5-13 (+S) - z5-5 (E) AUTO position Below 1 Ω z5-13 (+S) - z5-5 (E) Except AUTO position 10 kΩ or higher z5-11 (+1) - z5-5 (E) LO position Below 1 Ω z5-11 (+1) - z5-5 (E) Except LO position 10 kΩ or higher z5-12 (+2) - z5-5 (E) HI position Below 1 Ω z5-12 (+2) - z5-5 (E) Except HI position 10 kΩ or higher Front Washer Switch Tester Connection Condition Specified Condition z5-15 (WF) - z5-5 (E) ON position Below 1 Ω z5-15 (WF) - z5-5 (E) OFF position 10 kΩ or higher Auto Sensitivity Adjustment Switch Tester Connection Condition Specified Condition z5-4 (VR) - z5-5 (E) P1 position 1102 to 1218 Ω z5-4 (VR) - z5-5 (E) P2 position 570 to 630 Ω z5-4 (VR) - z5-5 (E) P3 position 256...
Categories
- Manuals Home
- Toyota Yaris Owners Manual
- Toyota Yaris Service Manual
- To Set Speed
- Auto Lock/Unlock Function
- Maintenance
- New on site
- Most important about car
Keys
To use the auxiliary key, press the knob and pull out the auxiliary key from the smart key.
