Toyota Yaris: Power Window Control System / Auto Up Operation does not Fully Close Power Window (Jam Protection Function is Activated)

Toyota Yaris XP210 (2020-2022) Reapir and Service Manual / Vehicle Exterior / Window / Glass / Power Window Control System / Auto Up Operation does not Fully Close Power Window (Jam Protection Function is Activated)

DESCRIPTION

If a door glass does not slide smoothly or a power window regulator motor assembly or door window regulator sub-assembly does not operate smoothly, the jam protection function may be triggered automatically, resulting in the auto up operation being unable to fully close the power window.

CAUTION / NOTICE / HINT

NOTICE:

  • If a power window regulator motor assembly has been replaced with a new one, initialize the power window control system.

    Click here

  • If a power window regulator motor assembly and door window regulator sub-assembly have been removed and installed, or if a power window regulator motor assembly was reused when a door glass or door glass run was replaced, initialize the power window control system.

    Click here

HINT:

This symptom may occur for any of the power windows.

PROCEDURE

1.

PERFORM INITIALIZATION (APPLICABLE LOCATION)

(a) Initialize the power window regulator motor assembly (applicable location).

Click here

NEXT

2.

CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP / DOWN FUNCTION (APPLICABLE LOCATION))

(a) Check that each power window moves when the auto up and down functions of the multiplex network master switch assembly or power window regulator switch assembly are operated.

Click here

OK:

Auto up and down functions are normal (applicable location).

OK

END (PROBLEM DUE TO INITIALIZATION FAILURE)

NG

3.

CHECK DOOR GLASS SLIDING MOVEMENT (APPLICABLE LOCATION)

(a) Remove the power window regulator motor assembly and door window regulator sub-assembly.

(b) Install the door glass to the door glass run.

(c) Check that the power window regulator motor assembly and door window regulator sub-assembly operate smoothly.

(d) Check that the door glass slides smoothly when sliding it up by hand.

NOTICE:

Make sure to perform initialization again.

HINT:

Ensure the following:
  • The door glass fits in the door glass run without improper contact or deformation.
  • Foreign matter is not caught in the door glass run.
  • The door glass run is not misaligned.
  • The door glass is not tilted and does not catch on the door glass run.

OK:

Door glass slides smoothly.

Result

Proceed to

OK (Driver door power window)

A

OK (Front passenger door power window)

B

NG

C

A

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door)

B

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door)

C

FIT DOOR GLASS CORRECTLY (REMOVE FOREIGN MATTER CAUSING IMPROPER FIT OR REPLACE PARTS)

    Key-off Operation Function Operates even if Operating Conditions are not Satisfied

    DESCRIPTION When the front doors are closed, each power window regulator motor assembly can be operated for approximately 45 seconds after the ignition switch is turned from on to off by receiving operation permission signals from the main body ECU (multiplex network body ECU)...

    Auto Down Operation does not Fully Open Power Window (Catch Protection Function is Activated)

    DESCRIPTION If a door glass does not slide smoothly or a power window regulator motor assembly or door window regulator sub-assembly does not operate smoothly, the catch protection function may be triggered automatically, resulting in the auto down operation being unable to fully open the power window...

    Other information:

    Toyota Yaris XP210 (2020-2022) Reapir and Service Manual: Terminals Of Ecu


    TERMINALS OF ECU CHECK POWER DISTRIBUTION BOX ASSEMBLY (a) Remove the power distribution box assembly. Click here (b) Reconnect the power distribution box assembly connectors. (c) Measure the voltage and resistance according to the value(s) in the table below...

    Toyota Yaris XP210 (2020-2022) Reapir and Service Manual: Diagnosis System


    DIAGNOSIS SYSTEM EURO-OBD (EUROPEAN SPEC) When troubleshooting Europe On-Board Diagnostic (Euro-OBD) vehicles, an OBD scan tool (complying with ISO 15765-4) must be connected to the vehicle. Various data output from the vehicle's ECM can then be read...

    Categories

    Refueling

    Before refueling, close all the doors, windows, and the liftgate/trunk lid, and switch the ignition OFF.

    To open the fuel-filler lid, pull the remote fuel-filler lid release.

    Toyota Yaris. Refueling

    To remove the fuel-filler cap, turn it counterclockwise. Attach the removed cap to the inner side of the fuel-filler lid.

    read more

     
    Copyright © 2022 www.toyaris4.com