Toyota Yaris: Automatic Transaxle Controls / Warning Light and Transaxle Ranges

Toyota Yaris XP210 (2020-2022) Owner's Manual / When Driving / Transaxle / Automatic Transaxle Controls / Warning Light and Transaxle Ranges

Warning Light

The warning light turns on when the system has a malfunction. Refer to Warning Lights.

Transaxle Ranges

  • The shift position indicator light in the combination meter illuminates. Refer to Warning/Indicator Lights.
  • The selector lever must be in P or N to operate the starter.

P (Park)

P locks the transaxle and prevents the front wheels from rotating.

R (Reverse)

In position R, the vehicle moves only backward. You must be at a complete stop before shifting to or from R, except under rare circumstances as explained in Rocking the Vehicle.

N (Neutral)

In N, the wheels and transaxle are not locked. The vehicle will roll freely even on the slightest incline unless the parking brake or brakes are on.

Apply the parking brake or depress the brake pedal before moving the selector lever from N to prevent the vehicle from moving unexpectedly.

D (Drive)

D is the normal driving position. From a stop, the transaxle will automatically shift through a 6-gearsequence.

M (Manual)

M is the manual shift mode position. Gears can be shifted up or down by operating the selector lever. Refer to Manual Shift Mode on.

WARNING

Always set the selector lever to P and set the parking brake when parking

Only setting the selector lever to the P position without using the parking brake to hold the vehicle is dangerous. If P fails to hold, the vehicle could move and cause an accident.

If the engine is running faster than idle, do not shift from N or P into a driving gear

It’s dangerous to shift from N or P into a driving gear when the engine is running faster than idle. If this is done, the vehicle could move suddenly, causing an accident or serious injury.

Do not shift into N when driving the vehicle

Shifting into N while driving is dangerous. Engine braking cannot be applied when decelerating which could lead to an accident or serious injury.

NOTICE

  • Shifting into P, N or R while the vehicle is moving can damage your transaxle.
  • Shifting into a driving gear or reverse when the engine is running faster than idle can damage the transaxle.
  • Do not shift into N when driving the vehicle. Doing so can cause transaxle damage.

    Shift Position Indication

    The selector position is indicated when the ignition is switched ON. Gear position indication In manual shift mode, the “M” of the shift position indication illuminates and the numeral for the selected gear is displayed...

    Active Adaptive Shift (AAS)

    Active Adaptive Shift (AAS) automatically controls the transaxle shift points to best suit the road conditions and driver input. This improves driving feel...

    Other information:

    Toyota Yaris XP210 (2020-2022) Reapir and Service Manual: Terminals Of Ecm


    TERMINALS OF ECM ECM HINT: The standard voltage and resistance of each ECM terminal is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard voltage or resistance for that pair of terminals shown in the "Specified Condition" column Use the illustration above as a reference for the ECM terminals...

    Toyota Yaris XP210 (2020-2022) Reapir and Service Manual: Terminals Of Ecu


    TERMINALS OF ECU ENGINE STOP AND START ECU (a) Disconnect the engine stop and start ECU connectors. (b) Measure the resistance and voltage according to the value(s) in the table below. Terminal No. (Symbol) Terminal Description Condition Specified Condition A66-1 (BIN2) - Body ground Auxiliary battery Always 9...

    Categories

    Fuel Gauge

    The fuel gauge shows approximately how much fuel is remaining in the tank when the ignition is switched ON. We recommend keeping the tank over 1/4 full.

    Toyota Yaris. Fuel Gauge

    Full 1/4 Full Empty

    read more

     
    Copyright © 2022 www.toyaris4.com