Toyota Yaris: Sfi System / VIN Not Programmed (P063051)

Toyota Yaris XP210 (2020-2024) Reapir and Service Manual / Engine & Hybrid System / G16e-gts (engine Control) / Sfi System / VIN Not Programmed (P063051)

MONITOR DESCRIPTION

DTC P063051 is stored when the Vehicle Identification Number (VIN) is not stored in the ECM or the stored VIN is not accurate.

DTC No.	Detection Item	DTC Detection Condition	Trouble Area	MIL	Note
P063051	VIN Not Programmed	Either of the following conditions is met (1 trip detection logic): The VIN is not stored in the ECM. The VIN written to the ECM is not accurate.	ECM	Comes on	SAE: P0630

MONITOR STRATEGY

Required Sensors/Components	ECM
Frequency of Operation	Continuous

CONFIRMATION DRIVING PATTERN

Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Wait 5 seconds or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the pending DTCs.
HINT:
- If a pending DTC is output, the system is malfunctioning.
- If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P063051.

Check the DTC judgment result.

GTS Display	Description
NORMAL	DTC judgment completed System normal
ABNORMAL	DTC judgment completed System abnormal
INCOMPLETE	DTC judgment not completed Perform driving pattern after confirming DTC enabling conditions

HINT:

If the judgment result is NORMAL, the system is normal.
If the judgment result is ABNORMAL, the system is malfunctioning.

CAUTION / NOTICE / HINT

HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE

1.	CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P063051)

(a) Read the DTCs.

Powertrain > Engine > Trouble Codes

NOTICE:

If P063051 is output, the VIN must be written to the ECM using the GTS. However, all DTCs are cleared automatically by the GTS when the VIN is written. If DTCs other than P063051 are output, troubleshoot them first.

Result	Proceed to
P063051 is output	A
P063051 and other DTCs are output	B

GO TO DTC CHART

WRITE VIN

(a) Write the VIN.

Click here

END

Fuel Pump "A" Control Circuit Short to Ground or Open (P062714)

DESCRIPTION Refer to DTC P062712. Click here DTC No. Detection Item DTC Detection Condition Trouble Area MIL Note P062714 Fuel Pump "A" Control Circuit Short to Ground or Open When the fuel pump control ECU operation duty ratio is 3 to 65%, the FPC terminal voltage is a certain value or less for 3 seconds or more (1 trip detection logic)...

Fuel Pump Control Module Internal Electronic Failure (P064A49)

MONITOR DESCRIPTION The fuel pump control ECU has a self-diagnosis function. If there is an internal malfunction, the fuel pump control ECU sends a malfunction signal to the ECM via the FPC drive circuit...

Other information:

Toyota Yaris XP210 (2020-2024) Reapir and Service Manual: Parts Location

PARTS LOCATION ILLUSTRATION *1 FRONT DOOR LOCK WITH MOTOR ASSEMBLY RH *2 FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY RH *3 FRONT DOOR LOCK WITH MOTOR ASSEMBLY LH *4 FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH *5 BACK DOOR OPENER SWITCH ASSEMBLY *6 BACK DOOR LOCK ASSEMBLY WITH COURTESY LIGHT SWITCH ILLUSTRATION *1 MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY *2 DOOR CONTROL SWITCH *3 MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) *4 POWER DISTRIBUTION BOX ASSEMBLY - ECU-IGR NO...

Toyota Yaris XP210 (2020-2024) Owner's Manual: Smart Key

Operation indicator light Operation buttons The operation indicator light flashes when the buttons are pressed. Lock button To lock the doors and the liftgate, press the lock button and the hazard warning lights will flash once. With the advanced keyless function: A beep sound will be heard once...