Toyota Yaris: Sfi System / Control Module Processor Watchdog/Safety MCU Failure (P060647)

Toyota Yaris XP210 (2020-2026) Reapir and Service Manual / Engine & Hybrid System / G16e-gts (engine Control) / Sfi System / Control Module Processor Watchdog/Safety MCU Failure (P060647)

MONITOR DESCRIPTION

The ECM continuously monitors its main CPU and monitor IC. This self-check ensures that the ECM is functioning properly. If outputs from main CPU and monitor IC are different and deviate from the standard, the ECM will illuminate the MIL and store this DTC.

DTC No.	Detection Item	DTC Detection Condition	Trouble Area	MIL	Note
P060647	Control Module Processor Watchdog/Safety MCU Failure	ECM main CPU malfunction (1 trip detection logic).	ECM	Comes on	SAE: P0606

MONITOR STRATEGY

Required Sensors/Components	ECM
Frequency of Operation	Continuous

CONFIRMATION DRIVING PATTERN

Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the GTS off.
Turn the ignition switch off.
Disconnect the GTS.
Disconnect the cable from the negative (-) auxiliary battery terminal and wait for 1 minute.
Connect the cable to the negative (-) auxiliary battery terminal.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Wait 1 second or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the pending DTCs.
HINT:
- If a pending DTC is output, the system is malfunctioning.
- If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P060647.

Check the DTC judgment result.

GTS Display	Description
NORMAL	DTC judgment completed System normal
ABNORMAL	DTC judgment completed System abnormal
INCOMPLETE	DTC judgment not completed Perform driving pattern after confirming DTC enabling conditions

HINT:

If the judgment result is NORMAL, the system is normal.
If the judgment result is ABNORMAL, the system is malfunctioning.

CAUTION / NOTICE / HINT

NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.
Click here
When disconnecting and reconnecting the auxiliary battery.
HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE

CLEAR DTC

(a) Clear the DTCs.

Powertrain > Engine > Clear DTCs

(b) Turn the ignition switch off.

2.	READ OUTPUT DTC (DTC P060647)

(a) Disconnect the cable from the negative (-) auxiliary battery terminal and wait for 1 minute.

(b) Connect the cable to the negative (-) auxiliary battery terminal.

(d) Read the DTCs.

Powertrain > Engine > Trouble Codes

Result	Proceed to
DTCs are not output	A
P060647 is output	B

CHECK FOR INTERMITTENT PROBLEMS

REPLACE ECM

Internal Control Module Random Access Memory (RAM) Error Data Memory Failure (P060444)

MONITOR DESCRIPTION The ECM continuously monitors its internal memory status. This self-check ensures that the ECM is functioning properly. The ECM memory status is diagnosed by internal mirroring of the main CPU and sub CPU to detect Random Access Memory (RAM) errors...

Control Module Performance Bank 1 Watchdog/Safety MCU Failure (P060747,P060787)

MONITOR DESCRIPTION The ECM continuously monitors its internal ICs and the monitor IC. If the monitor IC is abnormal, the ECM illuminates the MIL and stores DTC P060747...

Other information:

Toyota Yaris XP210 (2020-2026) Owner's Manual: Warning Lights

These lights turn on or flash to notify the user of the system operation status or a system malfunction. Master Warning Light Brake System Warning Light ABS Warning Light Charging System Warning Light Engine Oil Warning Light Check Engine Light High Engine Coolant Temperature Warning Light Automatic Transaxle Warning Light Power Steering Malfunction Indicator Light Air Bag/Front Seat Belt Pretensioner System Warning Light LED Headlight Warning Light Low Fuel Warning Light Check Fuel Cap Warning Light Seat Belt Warning Light (Front seat) Door-Ajar Warning Light Low Washer Fluid Level Warning Light Tire Pressure Monitoring System Warning Light KEY Warning Light Low Speed Pre-Collision System Warning Light * 1: The light turns on when the ignition is switched on for an operation check, and turns off a few seconds later or when the engine is started...

Toyota Yaris XP210 (2020-2026) Reapir and Service Manual: Inspection

INSPECTION PROCEDURE 1. INSPECT FOG LIGHT ASSEMBLY LH (a) Check that the fog light assembly LH. (1) Apply auxiliary battery voltage to the fog light assembly LH and check that the light comes on. OK: Condition Specified Condition A104-2 (B) - Auxiliary battery positive (+) A104-1 (E) - Auxiliary battery negative (-) Fog light assembly LH comes on If the result is not as specified, replace the fog light assembly LH...