Toyota Yaris: Power Integration System / Power Integration No.1 System Internal Failure (B235204)

Toyota Yaris XP210 (2020-2026) Reapir and Service Manual / Power Source & Network / Power Distribution / Power Integration System / Power Integration No.1 System Internal Failure (B235204)

DESCRIPTION

This DTC is output when the semiconductor power integration ECU detects a Internal circuit error.

DTC No.	Detection Item	DTC Detection Condition	Trouble Area
B235204	Power Integration No.1 System Internal Failure	Microcomputer abnormality AD circuit trouble	Semiconductor power integration ECU

WIRING DIAGRAM

Click here

CAUTION / NOTICE / HINT

NOTICE:

When using the GTS with the ignition switch off to troubleshoot:
Connect the GTS to the vehicle, and turn a courtesy switch on and off at 1.5 second intervals until communication between the GTS and vehicle begins.
Inspect the fuses for circuits related to this system before performing the following procedure.
Before performing troubleshooting, check whether there are any malfunctions with the lighting system.
Click here

PROCEDURE

CLEAR DTC

(a) Clear the DTCs.

Body Electrical > Power Integration No.1 > Clear DTCs

2.	CHECK FOR DTC

(a) Check for DTCs.

Body Electrical > Power Integration No.1 > Trouble Codes

Result	Proceed to
B235204 is output	A
B235204 is not output	B

REPLACE SEMICONDUCTOR POWER INTEGRATION ECU

USE SIMULATION METHOD TO CHECK

Vehicle Control History

VEHICLE CONTROL HISTORY NOTICE: Make sure to record any output Vehicle Control History codes before clearing them and checking the Vehicle Control History again...

Power Distribution Box System Internal Failure (B235504)

DESCRIPTION This DTC is output when the power distribution box assembly detects a Internal circuit error. DTC No. Detection Item DTC Detection Condition Trouble Area B235504 Power Distribution Box System Internal Failure Microcomputer abnormality AD circuit trouble The load drive output open or short trouble Power distribution box assembly WIRING DIAGRAM Click here CAUTION / NOTICE / HINT NOTICE: When using the GTS with the ignition switch off to troubleshoot: Connect the GTS to the vehicle, and turn a courtesy switch on and off at 1...

Other information:

Toyota Yaris XP210 (2020-2026) Reapir and Service Manual: Inspection

INSPECTION PROCEDURE 1. INSPECT STEERING WHEEL SWITCH HOUSING (a) Check the resistance. (1) Measure the resistance according to the value(s) in the table below. *a Component without harness connected (Steering Wheel Switch Housing) - - Standard Resistance: Light Switch Circuit Tester Connection Condition Specified Condition z6-3 (T) - z4-3 (T) Always Below 1 Ω z6-12 (H) - z4-4 (H) Always Below 1 Ω z6-7 (A) - z4-5 (A) Always Below 1 Ω z6-16 (HU) - z4-6 (HU) Always Below 1 Ω z6-11 (HF) - z4-7 (HF) Always Below 1 Ω z6-8 (TR) - z4-8 (TR) Always Below 1 Ω z6-14 (TL) - z4-9 (TL) Always Below 1 Ω z6-6 (CR) - z4-10 (CR) Always Below 1 Ω z6-13 (BFG) - z4-11 (BFG) Always Below 1 Ω z6-4 (B) - z4-12 (B) Always Below 1 Ω z6-5 (EL) - z4-13 (EL) Always Below 1 Ω Wiper Switch Circuit Tester Connection Condition Specified Condition z5-10 (W_OFF) - z4-24 (W_OFF) Always Below 1 Ω z5-13 (+S) - z4-25 (+S) Always Below 1 Ω z5-11 (+1) - z4-26 (+1) Always Below 1 Ω z5-12 (+2) - z4-27 (+2) Always Below 1 Ω z5-14 (MIST) - z4-28 (MIST) Always Below 1 Ω z5-15 (WF) - z4-31 (WF) Always Below 1 Ω z5-5 (E) - z4-33 (E) Always Below 1 Ω z5-4 (VR) - z4-34 (VR) Always Below 1 Ω If the result is not as specified, replace the steering wheel switch housing...

Toyota Yaris XP210 (2020-2026) Reapir and Service Manual: Automatic High Beam System does not Operate or Operation Indicator does not Illuminate

DESCRIPTION The main body ECU (multiplex network body ECU) controls the automatic high beam system based on signals received from the forward recognition camera. WIRING DIAGRAM CAUTION / NOTICE / HINT NOTICE: Before replacing the main body ECU (multiplex network body ECU), refer to Registration...