Toyota Yaris: Air Conditioning System / Recirculated/Fresh Air Modes do not Switch
DESCRIPTION
If the air inlet mode cannot be changed between recirculation/fresh or exhaust gas odors can be smelled even though recirculation mode is selected, the following factors may be the cause.
| Symptom | Factor |
-
Air inlet mode cannot be changed between recirculation/fresh
-
Exhaust gas odors can be smelled when air inlet mode set to recirculation mode
| -
No. 1 blower damper servo sub-assembly malfunction
-
Damper link disconnection
-
Air inlet damper mechanically locked
-
Engine coolant temperature (high)
-
Air conditioner unit assembly malfunction
|
PROCEDURE
| 1. | CHECK NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY |
(a) Check that the No. 1 blower damper servo sub-assembly is installed correctly.
Click here
OK:
The No. 1 blower damper servo sub-assembly is installed correctly.
| NG |
| INSTALL NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY |
|
OK |
| |
(a) Check for DTCs.
Body Electrical > Air Conditioner > Trouble Codes
| Result | Proceed to |
| B143A87 and B143B7F is not output | A |
| B143A87 is output | B |
| B143B7F is output | C |
| B |
| GO TO DTC B143A87 |
| C |
| GO TO DTC B143B7F |
|
A |
| |
| 3. | READ VALUE USING GTS (COOLANT TEMPERATURE) |
(a) Read the Data List according to the display on the GTS.
Powertrain > Engine > Data List
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
| Coolant Temperature | Engine coolant temperature | Min.: -40°C (-40°F), Max.: 140°C (284°F) | 75 to 100°C (167 to 212°F): After warming up | This is the engine coolant temperature. HINT: -
After warming up the engine, the engine coolant temperature will be 75 to 100°C (167 to 212°F).
-
After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature will be approximately equal.
-
If the value is -40°C (-40°F), or higher than 135°C (275°F), the sensor circuit is open or shorted.
-
Check if the engine overheats if the value indicated is higher than 135°C (275°F).
|
Powertrain > Engine > Data List
| Tester Display |
| Coolant Temperature |
OK:
The value of the display does not change frequently.
| OK |
| REPAIR OR REPLACE AIR CONDITIONER UNIT ASSEMBLY |
| NG |
| GO TO COOLING SYSTEM |
DESCRIPTION If recirculation/fresh mode changes unintentionally and without permission, the following causes are possible. Symptom Factor
Recirculation/fresh mode changes without permission
Recirculation/fresh mode light blinks
Customize setting
Change in ambient air temperature
Decrease in refrigerant pressure
Air conditioner pressure sensor circuit malfunction
Engine coolant temperature (high)
PROCEDURE 1...
DESCRIPTION If warm air blows from the registers regardless of the temperature setting of the air conditioning system, the following factors may be the cause...
Other information:
Use tar remover to remove road tar and insects. Never do this with
a knife or similar tool.
To prevent corrosion on bright-metal surfaces, apply wax or chrome
preservative and rub it to a high luster.
During cold weather or in coastal areas, cover bright-metal parts
with a coating of wax or preservative heavier than usual...
INSPECTION PROCEDURE 1. INSTALL OUTER MIRROR SWITCH ASSEMBLY (a) Check the mirror select and surface adjust switch. (1) Turn the mirror select and surface adjust switch to the L position.
*a Mirror Select and Surface Adjust Switch *b Component without harness connected (Outer Mirror Switch Assembly) (2) Measure the resistance according to the value(s) in the table below...
Categories

Smart key
Auxiliary key
Key code number plate
To use the auxiliary key, press the knob and pull out the auxiliary key
from the smart key.

read more